Searching for Interface Fastethernet0 1 Does Not Support User Settable information? Find all needed info by using official links provided below.
https://community.cisco.com/t5/switching/interface-fastethernet0-0-does-not-support-user-settable-mtu/td-p/1628063
% Interface FastEthernet0/0 does not support user settable mtu. Follow some informations: show diag Slot 0: Dual FastEthernet (RJ-45) I/O Card Port adapter, 2 ports Port adapter is analyzed Port adapter insertion time 7w6d ago EEPROM contents at hardware discovery: Hardware Revision : 1.2 Top Assy. Part Number : 800-07114-04
https://learningnetwork.cisco.com/thread/70875
May 20, 2014 · % Interface FastEthernet0/0 does not support user settable mtu. And i tried to setup ip mtu 1000, but i didn't see it changed here: I think i should know the diff. R2(config-if)#ip mtu 1000. R2(config-if)#do show int fa 0/0. FastEthernet0/0 is up, line protocol is up. Hardware is Gt96k FE, address is c202.7d84.0000 (bia c202.7d84.0000)
https://evilttl.com/wiki/mtu-on-cisco-routers
% Interface FastEthernet0 / 0 does not support user settable mtu. The same refers to switch interface cards. To check L3 MTU on an interface issue sh ip int {if-number} .
https://quickview.cloudapps.cisco.com/quickview/bug/CSCuz58508
Nov 27, 2019 · Symptom: Configuring MTU size for interfaces results in a message to console: % Interface GigabitEthernet1 does not support user settable MTU. Conditions: CSR1000v running Denali-16.3.1 and attempting to configure interface MTU size for interfaces that rely on polled mode drivers. Determining if an interface uses a polled mode driver is done by using the following show …
https://community.cisco.com/t5/routing/asr920-user-settable-mtu-on-bdi-interface-not-supported/td-p/2609912
ASR920 - user settable MTU on BDI interface not supported Hello, I am trying to integrate ASR920 into an existing MPLS network, but I am not able to change the MTU on the BDI interface.
https://www.experts-exchange.com/questions/27047799/How-can-I-change-MTU-on-FastEthernet-port-Cisco-7206.html
How can I change MTU on FastEthernet port (Cisco 7206) When I enter following commands #interface fastEthernet 0/0 #mtu 1524 I see next message % Interface FastEthernet0/0 does not support user settable …
https://community.cisco.com/t5/other-network-architecture/how-to-change-mtu-on-lan-interface/td-p/498325
Cisco 3745 router - I need to change LAN interface from 1500 to 4470 to match WAN interafce mtu. Is this possible? % Interface FastEthernet0/0 does not support user settable mtu.
https://ieoc.com/discussion/6244/mtu-change
Does anyone know why I can't change the mtu interface with this command ? Router(config-if)#mtu 9216 % Interface FastEthernet0/0 does not support user settable mtu.
https://community.cisco.com/t5/switching/fa0-2-port-doesn-t-show-up-on-show-vlan-vtp-port-assignment/td-p/710004
The configuration below still does not associated fa0/2 with VLAN 2. interface FastEthernet0/1. switchport trunk allowed vlan 1,3-1005. switchport mode trunk! interface FastEthernet0/2. switchport trunk encapsulation dot1q. switchport trunk allowed vlan 1,2,1002-1005. switchport mode trunk! VLAN Name Status Ports
https://community.cisco.com/t5/switching/how-to-create-subinterface-on-a-3560/td-p/1434951
You don't need to create subinterfaces on a L3 switch. Instead make the port a trunk port and then create a L3 SVI for each vlan you want to route eg.
How to find Interface Fastethernet0 1 Does Not Support User Settable information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.