Searching for Cisco Switches That Support Rspan information? Find all needed info by using official links provided below.
https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/10570-41.html
Jan 22, 2019 · RSPAN is an advanced feature that requires a special VLAN to carry the traffic that is monitored by SPAN between switches. RSPAN is not supported on all switches. Check the respective release notes or configuration guide to see if you can use RSPAN on the switch that you deploy.
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/network_management/configuration_guide/b_nm_15ex_2960-x_cg/b_nm_15ex_2960-x_cg_chapter_0111.html
On each switch, you can configure a maximum of 4 (2 if switch is stacked with Catalyst 2960-S switches) source sessions and 64 RSPAN destination sessions. A source session is either a local SPAN session or an RSPAN source session.
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-5/configuration_guide/nmgmt/b_165_nmgmt_9300_cg/b_165_nmgmt_9300_cg_chapter_0101.html
Nov 08, 2019 · Use Cisco Feature Navigator to find information about platform support and Cisco software image support. ... , the switch must be running the LAN Base image. ... Device (config-vlan)# remote-span: Specifies that the VLAN you specified in Step 5 is part of the RSPAN VLAN.
https://www.cisco.com/c/en/us/support/docs/smb/switches/cisco-350-series-managed-switches/smb5327-configure-remote-switch-port-analyzer-rspan-settings-on-the.html
Aug 06, 2019 · RSPAN VLANs must be configured on both Start and Final switches in VLAN configuration mode by using the remote-span VLAN configuration mode command, or follow the instructions below: Step 1. Log in to the web-based utility of the Start Switch and choose Advanced in the Display Mode drop-down list. Step 2. Choose VLAN Management > VLAN Settings. Step 3.
https://www.cisco.com/c/en/us/support/docs/switches/nexus-7000-series-switches/113438-rspan-nexus-7000-00.html
Apr 26, 2012 · The Nexus 7000 Series Switch is limited in what it can do with RSPAN. An RSPAN VLAN cannot be used as a SPAN destination. Therefore, the Nexus 7000 switch can only use RSPAN as a transit VLAN or a source VLAN and pull data from the RSPAN VLAN.
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960/software/release/12-2_55_se/configuration/guide/scg_2960/swspan.html
Oct 17, 2016 · You can run both a local SPAN and an RSPAN source session in the same switch stack. The switch stack supports a total of 66 source and RSPAN destination sessions. With the LAN Lite license, the switch supports configuration of only one SPAN session. You can have multiple destination ports in a SPAN session,...
https://community.cisco.com/t5/networking-documents/how-to-configure-span-and-rspan-on-cisco-catalyst-4500-switches/ta-p/3121308
RSPAN does not support BPDU packet monitoring or other Layer 2 switch protocols. The RSPAN VLAN is configured only on trunk ports and not on access ports. In order to avoid unwanted traffic in RSPAN VLANs, make sure that all participant switches support the VLAN remote-span feature.
https://community.cisco.com/t5/switching/rspan/td-p/3357445
My topology is SW4506 where I want to mirror port to RSPAN vlan, this switch is connected via trunk port to L3 switch 4510 and from 4510 via trunk to L2 switch 2960, which is my desired RSPAN destination port gi0/2. I have created special rspan vlan by commands. conf t -> vlan 66 -> remote-span->name RSPAN.
How to find Cisco Switches That Support Rspan information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
