Unable To Set Option Autosupport To

Searching for Unable To Set Option Autosupport To information? Find all needed info by using official links provided below.


Setting up AutoSupport - NetApp

    https://library.netapp.com/ecmdocs/ECMP1368862/html/GUID-91C43742-E563-442E-8161-17D5C5DA8C19.html
    Ensure that AutoSupport is enabled by setting the autosupport.enable option to on. If you want technical support to receive AutoSupport messages, set the following options: Set autosupport.support.enable to on. Select a transport protocol for messages to technical support by setting autosupport.support.transport to smtp, http, or https.

How to configure AutoSupport in Data ONTAP

    https://kb.netapp.com/app/answers/answer_view/a_id/1030087/~/how-to-configure-autosupport-in-data-ontap-
    The AutoSupport feature is enabled by default on the storage system. AutoSupport begins sending messages to technical support 24 hours after it is enabled. Configuration to complete AutoSupport setup: To complete AutoSupport configuration, fill in the following fields: Configure the 'from' address: 7-Mode

AutoSupport options - NetApp

    https://library.netapp.com/ecmdocs/ECMP1368862/html/GUID-BBCB6CA0-88BF-4C94-9048-9643769F4BAB.html
    You can have AutoSupport messages sent to your internal support organization by setting this option (or the autosupport.to option) and having a valid mail host. autosupport.ondemand.polling_interval: Defines the rate at which the node polls the AutoSupport On Demand service. This option is not editable at the admin privilege level.

How to set up AutoSupport - NetApp

    https://kb.netapp.com/app/answers/answer_view/a_id/1030460/~/how-to-set-up-autosupport-
    HTTPS is the default. If the network connection does not allow HTTPS or HTTP, configure AutoSupport for SMTP. To use HTTP or HTTPS to send AutoSupport messages, configure an HTTP or HTTPS proxy. The autosupport.support.proxy option allows an HTTP proxy to be set, if necessary. This is useful only if autosupport.support.transport is HTTP or ...

Setting up AutoSupport - NetApp Documentation

    http://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sag/GUID-91C43742-E563-442E-8161-17D5C5DA8C19.html
    Set -transport to https. If you use a proxy, set -proxy-url to the URL of your proxy. This configuration supports communication with AutoSupport OnDemand and uploads of large files. Use HTTP that is preferred over SMTP. Set -transport to http. If you use a proxy, set -proxy-url to the URL of your proxy.

IBM System Storage N series AutoSupport Overview

    https://www.ibm.com/support/knowledgecenter/nseries/com.ibm.nseries.hardware.doc/gc26785405.pdf
    IBM System Storage N series AutoSupport Overview ... Up to five email addresses can be set for each AutoSupport mail option: v The autosupport.noteto option provides for a "short note" email message containing the reason for the notification in the subject line and the time of failure. These messages are triggered only by specific

Enabling or disabling AutoSupport settings

    http://docs.netapp.com/ontap-9/topic/com.netapp.doc.onc-sm-help-930/GUID-B2D49A65-CACC-40D3-ACF5-1D2CEDCA3105.html
    AutoSupport messages enable you to monitor your storage system health or send notifications to technical support and your internal support organization. About this task. The AutoSupport option is enabled by default. Steps. Click > AutoSupport. Select the node, and then click Enable or Disable. Click OK. Verify that the AutoSupport status ...

How to add recipients to the autosupport e-mail ... - Dell EMC

    https://community.emc.com/docs/DOC-38946
    Sep 18, 2014 · # autosupport show all . To add the datadomain autosupport email for tracking alerts. DD OS 5.x and lower: # autosupport add [email protected] . DD OS 5.x and later, addresses can be added to the alert list and autosupport list separately: # autosupport add {alert-summary asup-detailed} emails <email_list> e.g.

Autosupport Configuration - Zerowait

    https://www.zerowait.com/netapp/autosupport-configuration
    Zerowait is the leading provider of third party NetApp support. Our knowledgeable staff and extensive inventory allow us to provide affordable, OEM quality support on NetApp products, including those that NetApp has declared EOL

Enable or disable AutoSupport features

    https://mysupport.netapp.com/NOW/public/eseries/sam/GUID-8538272A-B802-49D9-9EA2-96C82DAD26A2/GUID-A0E0435F-ED98-4666-B57A-86C3563C9BCB.html
    Select the check boxes next to the AutoSupport features that you want to enable. The features depend on each other as indicated by the indentation of the items in the dialog box. For example, you must enable AutoSupport OnDemand before you can enable Remote Diagnostics.



How to find Unable To Set Option Autosupport To information?

Follow the instuctions below:

  • Choose an official link provided above.
  • Click on it.
  • Find company email address & contact them via email
  • Find company phone & make a call.
  • Find company address & visit their office.

Related Companies Support