Non Cisco Wgb Support

Searching for Non Cisco Wgb Support information? Find all needed info by using official links provided below.


WGB Roaming: Internal Details and Configuration - Cisco

    https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1130-ag-series/113198-wgb-roam-config.html
    Aug 26, 2011 · Non Cisco WGB: This is a third party device acting as a WGB, connecting one or more wired devices to the wireless infrastructure. These do not support IAPP, and either allow only a single wired device, or provide a MAC address translation mechanism, hiding all their wired clients behind a single 802.11 MAC address.

Cisco Wireless Controller Configuration Guide, Release 8.3 ...

    https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-3/config-guide/b_cg83/b_cg83_chapter_0101100.html
    Jun 15, 2018 · Restrictions for Non-Cisco Workgroup Bridges. Only Layer 2 roaming is supported for WGB devices. Layer 3 security (web authentication) is not support for WGB clients. Visibility of wired hosts behind a WGB on a controller is not supported because the non-Cisco WGB device performs MAC hiding. Cisco WGB supports IAPP.

Release Notes for Cisco Wireless LAN Controllers and ...

    https://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn7_0_116_0.html
    Non-Cisco WGB Support. Starting in release 7.0.116.0, the controller software has been updated to accommodate non-Cisco workgroup bridges so that the controller can forward ARP, DHCP, and data traffic to and from the wired clients behind workgroup bridges. This processes is accomplished by enabling the passive client feature.

WGB - Workgroup bridge only works in un... - Cisco Community

    https://community.cisco.com/t5/other-wireless-mobility-subjects/wgb-workgroup-bridge-only-works-in-universal-mode/td-p/2825938
    Just to verify: yes, you need to have the "Aironet IE extensions" enabled on your SSID to support the "default" WGB Cisco implementation. When you use "universal mode" the access-point spoofs the specified MAC address so that the wireless infrastructure has no idea that the access-point is in between.

Unstable WGB on WLC - Cisco Community

    https://community.cisco.com/t5/other-wireless-mobility-subjects/unstable-wgb-on-wlc/td-p/1958770
    The Non-Cisco WGB feature is supported only on the 5508, 2500 and 2100 Controllers. NPU based platforms (4400/wism/3750w) do not support this feature. #however, you could try adding the 3rd party wgb mac address to WLC's mac filter list and test with simple to …

Can you connect non-cisco AP's to a Cis... - Cisco Community

    https://community.cisco.com/t5/other-wireless-mobility-subjects/can-you-connect-non-cisco-ap-s-to-a-cisco-wlc-controller/td-p/1342711
    Re: Can you connect non-cisco AP's to a Cisco WLC Controller There are a number of "foreign AP" subcommands found in CLI but there are no official documentations as of yet. For obvious reasons, Cisco will officially "not"support non-Cisco LAP to their WLC.

AP1262 bridge to Non-Cisco Access Point... - Cisco Community

    https://community.cisco.com/t5/wireless-and-mobility/ap1262-bridge-to-non-cisco-access-point/td-p/2456976
    I would like to use a Cisco AP1262 in a mobile command vehicle to bridge to any WiFi Access Point that I know the SSID and Pasword to. Will the 1262 Bridge to a Non-Cisco Access Point? If so, any assistance in finding an example configuration would

Cisco Aironet Workgroup Bridge FAQ - Cisco

    https://www.cisco.com/c/en/us/support/docs/wireless/aironet-340-series/8018-workgroup-bridge-faq.html
    Jul 31, 2007 · The 340 WGB runs VxWorks, and new Cisco IOS products (such as the br1310) have adapted the WGB, root/non-root bridge, and AP functionality. Q. What is the default IP address of a WGB? A. ... A Cisco WGB device does not support multiple VLANs in it. A 1100 AP, however, that acts in WGB mode can support multiple VLANs in it but with these ...

Universal Workgroup Bridge feature on A... - Cisco Community

    https://community.cisco.com/t5/wireless-mobility-documents/universal-workgroup-bridge-feature-on-autonomous-access-points/ta-p/3132608
    Core Issue. 1200 series autonomous access points can support Universal Workgroup Bridge mode. With this feature , access point configured in workgroup bridge mode can also associate to non-cisco APs.WGB assoicates as a client and only a single wired client can be connected with the Universal WGB.



How to find Non Cisco Wgb Support information?

Follow the instuctions below:

  • Choose an official link provided above.
  • Click on it.
  • Find company email address & contact them via email
  • Find company phone & make a call.
  • Find company address & visit their office.

Related Companies Support