Searching for Joist Support Bathtub information? Find all needed info by using official links provided below.
https://www.thisoldhouse.com/ask-toh/support-heavy-tub
The joists in houses that age and newer should be plenty strong enough to bear the weight of the tub, even when filled with water. However, it's possible that someone cut through the middle of a joist or two to install heating ducts, or drilled big holes to run drainpipe, or made notches for supply pipes.
https://homeguides.sfgate.com/floor-framing-bathtubs-51932.html
The floor framing for bathtubs requires special attention. You must consider all of the weight the floor joists must be able to support. A standard bathtub can hold between 40 and 60 gallons of water.
https://www.doityourself.com/stry/how-to-reinforce-a-deck-to-support-a-hot-tub
So if your decking joists run right to left, your 4x4 support will mount front to back. You can mount them using metal hangers made for this purpose. Step 4 - Place the Footers. Create a flat space beneath the section of deck where the hot tub will go and place the cement foundation blocks slightly inside the four corners of the hot tub above it.
https://www.ehow.com/how_8055964_support-new-tub-doesnt-flex.html
How to Support a New Tub So It Doesn't Flex F.R.R. Mallory Pin Share Tweet ... Most people have walked across a floor or deck that flexes because the joists are too far apart and the subfloor is too thin for the load. In addition, fiberglass or acrylic tubs are not as rigid as cast iron tubs. Bottom line: If the underside of a bathtub isn't ...
https://community.screwfix.com/threads/no-joist-to-support-the-floor-under-the-bath-tub.212456/
Jul 05, 2019 · No joist to support the floor under the bath tub. Discussion in ... which should do the job supporting floor under a bed or a wardrobe. I do not think this would do the trick to support a bathtub full of water with me and my missus in it. ... half way across the first of the double joist with a multitool so there was some bearing of the boards ...
https://www.hunker.com/13402355/does-a-floor-need-extra-support-when-installing-a-cast-iron-tub
Regardless of this weight difference though, most standard floors have the strength to support a cast iron tub. While floors do need extra support when installing a cast iron tub, in some instances, such as in older homes, you may choose to reinforce the floor prior to a tub's installation for safety. Floor Maximum Load. With the standard joist ...
https://diy.stackexchange.com/questions/128670/can-the-floor-framing-in-my-1930s-bathroom-support-my-tub-and-shower
Because the tub/shower area exceeds the allowable loads supported by 2x6 @ 16” oc, it will deflect and crack the tile floor and gypsum board ceiling below. I recommend adding 1 joist on each side of the existing joist under the tub. Make sure it fits tight against the subfloor, because new 2x6’s are smaller than your 1930 2x6’s.
https://www.aconcordcarpenter.com/reinforcing-a-floor-joist.html
Many times I will apply scabs to floor joists that were previously or will currently be notched or drilled to install plumbing pipes. Note – the photos show a recent bathroom remodel where we relocated the tub drain across several floor joists. the floor system is 2×10 joists spaced 12 inches on center.
https://answers.yahoo.com/question/index?qid=20111121125144AAkqF30
Nov 21, 2011 · I want to know if my 2x8 floor joists are strong enough to support a cast iron tub (350lb) while full of water (350lb) and with a person (250lb) in it. I would like the tub to run parallel with the 2x8 joists (spanning 12' at 16" ctrs). The entire front edge of the tub would be sitting on the floor above a joist while the back side of the tub has 2 small feet (1 at each end) also directly ...
https://www.thebuildingcodeforum.com/forum/threads/support-for-bathtub.6191/
Mar 09, 2012 · -- The rigid nature of the bath tub distributes the loads in ways that reduces the effect on individual members.-- There are often partitions on the floor below that reduce the spans on the joists under the bathtub. When the spans are really long the member is controled by deflection consideations.
https://www.thisoldhouse.com/ask-toh/support-heavy-tub
The joists in houses that age and newer should be plenty strong enough to bear the weight of the tub, even when filled with water. However, it's possible that someone cut through the middle of a joist or two to install heating ducts, or drilled big holes to run drainpipe, or made notches for supply pipes.
https://homeguides.sfgate.com/floor-framing-bathtubs-51932.html
The floor framing for bathtubs requires special attention. You must consider all of the weight the floor joists must be able to support. A standard bathtub can hold between 40 and 60 gallons of water.
https://www.hunker.com/13402355/does-a-floor-need-extra-support-when-installing-a-cast-iron-tub
Regardless of this weight difference though, most standard floors have the strength to support a cast iron tub. While floors do need extra support when installing a cast iron tub, in some instances, such as in older homes, you may choose to reinforce the floor prior to a tub's installation for safety. Floor Maximum Load. With the standard joist ...
https://community.screwfix.com/threads/no-joist-to-support-the-floor-under-the-bath-tub.212456/
Jul 05, 2019 · No joist to support the floor under the bath tub. Discussion in ... which should do the job supporting floor under a bed or a wardrobe. I do not think this would do the trick to support a bathtub full of water with me and my missus in it. ... half way across the first of the double joist with a multitool so there was some bearing of the boards ...
https://www.housebeautiful.com/uk/renovate/diy/advice/a1372/bathroom-floor-test-strength-advice/
Mar 14, 2017 · Installing a cast-iron bath? Here's how to strengthen bathroom floor joists ... strong enough to support the weight of a cast-iron bath filled with water, and a …
https://www.ehow.com/how_8055964_support-new-tub-doesnt-flex.html
How to Support a New Tub So It Doesn't Flex F.R.R. Mallory Pin Share Tweet ... Most people have walked across a floor or deck that flexes because the joists are too far apart and the subfloor is too thin for the load. In addition, fiberglass or acrylic tubs are not as rigid as cast iron tubs. Bottom line: If the underside of a bathtub isn't ...
https://www.decksgo.com/joist-size-for-hot-tub-deck.html
Joist Size for Hot Tub Deck. by John Stuart (Calgary, AB) I'm struggling to find the appropriate materials for the lower portion of a 2 tier deck that will be supporting a hot tub. The lower deck structure is 10'x10' ledger to beam construction.
How to find Joist Support Bathtub information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
