Searching for Cardbus Yenta Compatible Bridge Support information? Find all needed info by using official links provided below.
https://how-to.fandom.com/wiki/How_to_configure_the_Linux_kernel/drivers/pcmcia
(on/off/module) CardBus yenta-compatible bridge support; depends on PCI select CARDBUS if !EMBEDDED select PCCARD_NONSTATIC This option enables support for CardBus host bridges. Virtually all modern PCMCIA bridges are CardBus compatible. A "bridge" is the hardware inside your computer that PCMCIA cards are plugged into.
https://debian-administration.org/article/405/Mounting_a_CF_card_via_PCMCIA_adapter
Jun 15, 2006 · This was solved by adding NLS (Native Language Support) to the kernel, then building the Codepage 437 (United States, Canada) kernel module. Overall though, fairly simple and straightforward process. [0x07] Credits
https://wiki.archlinux.org/index.php/Dell_Latitude_C600
If you're compiling your own kernel remember that this is a yenta-compatible cardbus and that should be enabled in the pccard section of the kernel config. …
https://wiki.gentoo.org/wiki/PC-Card
The pccardctl command (part of the sys-apps/pcmciautils package) can be used to show information about the PC-Card controller and the inserted cards. It can also be used to load and unload PC cards. It can also be used to load and unload PC cards.
http://www.ti.com/sc/docs/products/msp/intrface/pci/tech.htm
The PCI1131 is a bridge between the PCI system bus and two PC Card sockets. The PCI1220, and PCI1250A are TI's third-generation PC Card controllers. The 12xx series controllers all support the PCI Power Management 1.0 specification and are PC 97 compliant.
http://pcmcia-cs.sourceforge.net/specs/5C475E.pdf
The 5C475 can support the 32-bit CardBus(Card-32) and the 16-bit PC card(Card-16) without external buffers. Concerning the card control interface, the 5C475‘s register is compatible with the Intel 82365SL and Ricoh’s RF5C396/366 in order to maintain backward compatibility with the …
http://files.kroah.com/lkn/lkn_pdf/ch08.pdf
PCCARD (PCMCIA/CardBus) support [M] PCCard (PCMCIA/CardBus) support 3. Enable both PCMCIA and CardBus support to cover the widest range of devices: Bus options (PCI, PCMCIA, EISA, MCA, ISA) PCCARD (PCMCIA/CardBus) support [M] PCCard (PCMCIA/CardBus) support [M] 16-bit PCMCIA support [*] 32-bit CardBus support
https://www.linuxquestions.org/questions/linux-kernel-70/kenrel-for-atiixp-with-dma-and-yenta-cardbus-support-442102/
May 12, 2006 · Kenrel for ATIIXP with DMA and Yenta cardbus support I have ran into a problem where all 2.4 kernels will support cardbus cards for my laptop but not DMA. 2.6.10 and lower will also support cardbus cards but not DMA. 2.6.11+ will support DMA but not cardbus cards.
https://wiki.gentoo.org/wiki/Texas_Instruments_PCIxx12
02:06.0 CardBus bridge [0607]: Texas Instruments PCIxx12 Cardbus Controller [104c:8039] Subsystem: Hewlett-Packard Company PCIxx12 Cardbus Controller [103c:30aa] Flags: bus master, medium devsel, latency 168, IRQ 18 Memory at e8100000 (32-bit, non-prefetchable) [size=4K] Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 Memory window 0: ec000000-efffffff …
https://forums.gentoo.org/viewtopic-t-167088-start-0.html
Aug 20, 2004 · Code: <*> PCMCIA/CardBus support [*] Enable PCMCIA debugging <*> CardBus yenta-compatible bridge support < > i82092 compatible bridge support
How to find Cardbus Yenta Compatible Bridge Support information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.