Searching for Bathtub Floor Support information? Find all needed info by using official links provided below.
https://homeguides.sfgate.com/build-tub-support-23623.html
1. Measure the width -- typically 30 to 36 inches -- of the tub planned for the installation, Include any nailing flange in the width. If the width is 32 inches, you can stick to a standard floor ...
https://homeguides.sfgate.com/floor-framing-bathtubs-51932.html
The floor framing for bathtubs requires special attention. You must consider all of the weight the floor joists must be able to support. A standard bathtub can hold between 40 and 60 gallons of water.
https://www.thisoldhouse.com/ask-toh/support-heavy-tub
Or perhaps a persistent leak has weakened the joists. A sagging, soft, or loose floor, or a cracked, water-stained ceiling in the room below are good indications that something is wrong. But even if the floor seems solid, play it safe and investigate the situation before you lug that tub up there.
https://www.diychatroom.com/f7/bathtub-floor-support-57677/
Nov 22, 2009 · Bathtub Floor Support. Thanks for taking the time to read and reply to my post. Here is more detail: The joist span 10.5 ft. The tub ledger is offset 1.5" parallel from the joist, underneath, the plywood is blocked (not x-braced) with 2x4's flat to the next joist every 16". Then there are 1x6's spanning the length of the joists under the 2x4's.
https://www.thebuildingcodeforum.com/forum/threads/support-for-bathtub.6191/
Mar 09, 2012 · Support For Bathtub. Discussion in 'Residential Structural Codes' started by 4thorns, Mar 6, 2012. Page 1 of 3 1 2 3 Next > 4thorns Bronze Member. Joined: Jul 7, 2011 ... The bigger concern would be the ability of the floor decking to support if legs did not rest directly over a joist. Modern cast iron tubs provide more bearing area so that the ...
https://www.ehow.com/how_8055964_support-new-tub-doesnt-flex.html
How to Support a New Tub So It Doesn't Flex F.R.R. Mallory Pin Share ... In addition, fiberglass or acrylic tubs are not as rigid as cast iron tubs. Bottom line: If the underside of a bathtub isn't supported well, the floor and tub material are likely to flex. Things You'll Need …
https://www.hunker.com/13402355/does-a-floor-need-extra-support-when-installing-a-cast-iron-tub
If the floor was built using the general 16-inch spacing, you can expect a bathroom floor to safely hold 40 psf. So, a 5-by-10 foot bathroom floor generally supports up to 2,000 pounds. This provides sufficient support for most cast iron bathtubs, which run under 500 pounds, even when full.
https://terrylove.com/forums/index.php?threads/how-to-fix-flex-in-the-bottom-of-a-bathtub.33292/
Jan 19, 2017 · support Get a can, or cans, of low expansion foam. Put a long piece of plastic tubing on the end of the nozzle, then slide the tubing under the tub and start shooting the foam in as you pull the tube out. It will glue the tub to the floor, but that will only be a minor problem when, and if, the tub is removed someday.
https://www.rehabmart.com/category/bathroom_support_rails.htm
in or out of the tub or shower, and also provide extra support while standing in the shower. Toilet Support Rails Enhancing safety specifically for commode use, toilet grab bars are another vital aid in preventing accidents in the bathroom. These support solutions come …
https://www.youtube.com/watch?v=NlYSi-klhIk
Jun 29, 2016 · Most bathtubs are usually supported by the front apron or front of the bathtub bottom, back overhang and by either legs attached to the bottom or some type of …
How to find Bathtub Floor Support information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
