Searching for Which Protocol Does Not Support Vlsm information? Find all needed info by using official links provided below.
https://lernccna.blogspot.com/2011/05/which-of-following-routing-protocols-do_02.html
Which of the following routing protocols do NOT su... Which of the following routing protocols support t... You need to choose a routing protocol for a new Te... Which of the following routing protocols do NOT su... You need to configure a single router into load ba... In network that support VLSM, which network mask s...
https://www.skillset.com/questions/which-one-of-the-following-routing-protocols-do-not-support-vlsm-and-cidr
Routing Information Protocol is a distance-vector routing protocol with three versions; RIPv1, RIPv2, and RIPng. RIPv1 is a classful routing protocol, thus, VLSM and CIDR is not supported. RIPv2 is the enhanced version of RIPv1. It is a classless routing protocol, thus, supports VLSM and …
https://lernccna.blogspot.com/2009/12/which-of-following-routing-protocols-do.html
Which of the following routing protocols do NOT su... You are a network administrator and you need to im... In network that support VLSM, which network mask s... What is the maximum number of IP addresses that ca... If an Ethernet port on router was assigned an IP a... Which of the following IP addresses is a private I...
https://quizlet.com/109631539/chapter-20-flash-cards/
B (RIP-2) , C (EIGRP) , and D (OSPF) . Classless routing protocols, by definition, support VLSM because classless routing protocols transmit the subnet mask in their routing updates. Of the listed answers, only RIP version 1 (RIP-1) is not a classless routing protocol.
https://quizlet.com/40414575/review-questions-and-ch-891011-flash-cards/
RIPv1 is support for VLSM information. D. IGRP does not support VLSM. Like RIP version 2, EIGRP is the updated version of IGRP, which provides support for VLSM. F. VLSM is the feature that is required to support non-contiguous networks, but VLSM is not itself a routing protocol
https://upskilld.com/learn/vlsm-subnetting-in-networks/
This is called classful routing and it does not support VLSM because there is no way for routers to communicate different sized subnets. The original Routing Information Protocol (RIPv1) is a classful routing protocol and therefore cannot support VLSM.
https://community.cisco.com/t5/switching/classful-vs-classless-routing-protocols/td-p/726119
A classful routing protocol does not support VLSM/discontiguous networks because they do not advertise the subnet mask with routing updates. So if you had 10.1.0.0/24 on R1 and 10.2.0.0/24 on R2 and both were advertising to R3 using RIPv1, then R3 would just simply see two routes for 10.0.0.0/8, one from each of the routers.
https://quizlet.com/168431660/chapter-22-variable-length-subnet-masks-flash-cards/
An inherent characteristic of a routing protocol, specifically that the routing protocol does not send subnet masks in its routing updates, thereby removing any need to make assumptions about the address in a particular subnet or network, making it …
https://learningnetwork.cisco.com/thread/74284
Aug 29, 2014 · Because it does not, Router 1 drops the network, and does not advertise the route. Router 1 now checks whether 131.108.7.0/30 is part of the same major net as 131.108.6.0/30, which is the network assigned to the interface that will be sourcing the update.
https://quizlet.com/249306711/network-technology-chapter-8-questions-flash-cards/
What protocol was adopted in 1994, and is now considered obsolete except for small, private WANs? RIPv2. Which protocol is a distance vector routing protocol? RIPv1. Which routing protocol does not support Variable-Length Subnet Masking (VLSM)? 1.33457. Which of the following could be a valid Autonomous System Number (ASN)?
How to find Which Protocol Does Not Support Vlsm information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
