Searching for Sonicwall Nsa 2400 Ipv6 Support information? Find all needed info by using official links provided below.
https://www.sonicwall.com/support/
SonicWall Support Services. Review our Support Offerings and Policies. Contact Support. Create a support ticket or contact us by phone. PSIRT. Product Security Incident Response Team. Product Life Cycle Tables. Identify the current life cycle phase of your product and understand eligibility for support and and new release downloads.
https://www.sonicwall.com/support/knowledge-base/how-to-disable-ipv6-traffic-on-an-interface/170503542484357/
The IPv6 is enabled by default on devices running 5.9 or 6.2 versions of firmware. This article explains how to disable IPV6 traffic on an Interface if you want to pass only IPv4 traffic. RESOLUTION: Navigate to Network Interfaces on your Sonicwall Firewall device. Select IPv6 …
https://www.sonicwall.com/support/knowledge-base/ipv6-bgp-support/170505328512401/
A SonicWall security appliance with IPv6 BGP support can replace a traditional BGP router on the edge of a network's AS. IPv6 BGP can be enabled on the Network > Routing page, but must be configured on the SonicOS Command Line Interface (CLI). Note: MPLS/VPN and multi cast are not supported for IPv6 BGP in SonicOS 6.2.0.0.
https://www.sonicwall.com/support/knowledge-base/configuring-the-sonicwall-ipv6-dhcpv6-server/170505365235841/
Configuring the SonicWall IPv6 DHCPv6 Server. RESOLUTION: Feature/Application: The Dynamic Host Control Protocol for IPv6 (DHCPv6) can provide a device with IPv6 addresses assigned by a DHCP server and other configuration information. IPv6 Clients listen for DHCP messages on UDP port 546.
https://www.sonicwall.com/support/knowledge-base/how-do-i-configure-nat-policies-for-ipv6-to-ipv4-traffic/190122012317986/
How do I configure NAT policies for IPv6 to IPv4 traffic? 12/26/2019 22 3468. DESCRIPTION: As a NAT64 translator, SonicOS allows an IPv6-only client from any zone to initiate communication to an IPv4-only server with proper route configuration. SonicOS maps IPv6 addresses to IPv4 addresses so IPv6 traffic changes to IPv4 traffic and vice versa.
http://help.sonicwall.com/help/sw/eng/6110/26/2/3/content/Appendix_D_IPv6.130.4.htm
This can be beneficial in some mobile environments, such as with Mobile IPv6. Dell SonicWALL’s implementation of IPv6 is full conformable with RFC 4861 in Router and Prefix Discovery. ... Wire mode is supported on NSA 2600 and higher ... the configuration is identical for IPv6 and IPv4, except for the fact that IPv6 only support IKEv2 mode ...
https://community.spiceworks.com/topic/2120072-disable-aggressive-mode-and-ikev1-on-sonicwall-nsa2400
Mar 13, 2018 · We are getting flagged for our NSA 2400 supporting Aggressive Mode with Pre-Shared Key. All of our Site-to-Site VPNs are configured for IKEv2. The only thing that has IKEv1 is the "WAN GroupVPN". Is it possible that is what's being detected? Can I just disable it? Is there any other way to disable Aggressive Mode and/or IKEv1 altogether? Thanks.4.5/5(10)
How to find Sonicwall Nsa 2400 Ipv6 Support information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
