Searching for Solaris Npiv Support information? Find all needed info by using official links provided below.
https://docs.oracle.com/cd/E23824_01/html/E23097/ggodz.html
NPIV is supported only in a Fabric topology. It is not supported in an FC-AL or point-to-point topology. Not all hardware supports NPIV. Both switches and HBAs (although not targets) must support NPIV in a SAN. By specification, HBAs should support up to 255 virtual ports, although this is defined by the resources on the switch.
https://docs.oracle.com/cd/E36784_01/html/E36836/ggokr.html
If you try to create an NPIV port on an HBA that supports NPIV but it is attached to a switch which does not support NPIV, the port will be created with an offline status. The status will be reported in the fcinfo(1M) output. Become an administrator. Create an NPIV port.
https://support.oracle.com/knowledge/Sun%20Microsystems/2108444_1.html
Note: Unless source and destination devices support direct-connect NPIV, a NPIV capable FC Switch is usually required between the FC HBA and the storage device. The objective of this document is to show how we can use NPIV feature on a control domain, in combination with new feature vsan / vhba, available on Solaris 11.3 or greater.
https://community.oracle.com/thread/3804023
Oct 16, 2015 · Direct NPIV support is currently not available in OVM for SPARC, but you can still check this below URL if this can help you : ... and maybe in Ldom solaris is a bit different. I think this is very similar. If you run ldm list-io -l you will be able to see the number of VF you card support I don't have and HBA card in my box so I show the ...
https://support.oracle.com/knowledge/Sun%20Microsystems/1609077_1.html
It DOES NOT APPLY to Solaris Servers that uses Oracle Virtual Domain (OVM) technology that configures Control DOmains (CDOM) virtualization technology to present virtualized HBA via SR-IOV, DIO or vSAN/vHBA to Logical Domains (LDOM). In which case NPIV is enabled by default. But you will still see this line in fcinfo hba-port output:
https://www.experts-exchange.com/questions/26399559/Does-Solaris-10-10-09-release-have-NPIV-support-for-LDOMs.html
These just show that Emulex has support for NPIV. QLogic also has such support. This does not mean that Solaris actually supports NPIV functionality for LDOMs.
https://docs.broadcom.com/docs-and-downloads/oem/support/solaris/sfs/240s/solarissfs.pdf
The StorEdge SAN foundation Software (SFS) driver and utilities support the following operating systems: † Solaris 10 SPARC † Solaris 10 x64 and x86 † OpenSolaris for SPARC † OpenSolaris for x64 and x86 For a list of adapters that are compatible with this driver, see the driver's Downloads page on …
http://www-01.ibm.com/support/docview.wss?uid=ssg1S1005826
NPIV mode on SVC or Storwize is only supported when used with Brocade or Cisco fibre channel SAN switches which are NPIV capable. Nodes in an IO group cannot be replaced by nodes with less memory when compressed volumes are present
https://docs.broadcom.com/docs-and-downloads/oem/support/elx/rt11.0.1/11.0.243.17/solaris_manual_elx.pdf
The NIC driver supports the Solaris Ethernet stack, including NIC virtualization (Crossbow), vSwitch, and vRouter.
How to find Solaris Npiv Support information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.