Searching for Netapp Change Autosupport Mail information? Find all needed info by using official links provided below.
https://library.netapp.com/ecmdocs/ECMP1366832/html/system/node/autosupport/modify.html
Use this parameter to specify up to five SMTP mail hosts through which the node sends AutoSupport messages. This parameter is required if you specify e-mail addresses in the -to, -noteto, or -partner-address parameters or if you specify smtp in the -transport parameter.
https://kb.netapp.com/app/answers/answer_view/a_id/1030087/~/how-to-configure-autosupport-in-data-ontap-
Define the list of recipients who will receive AutoSupport e-mail notifications regardless of the severity level. ... Run the following command to change the transport settings: ... the AutoSupport data has to be collected manually. See KB 1010077: How to manually send AutoSupport files to NetApp. In certain scenarios, there might be issues ...
https://kb.netapp.com/app/answers/answer_view/a_id/1030460/~/how-to-set-up-autosupport-
To set up AutoSupport, specify the mail hosts, the addresses for AutoSupport mail, the storage system administrator's address, set up the command to send an immediate message, and specify the recipients of short e-mail messages sent by AutoSupport. Specify mail hosts: The command to specify hosts that send AutoSupport e-mail messages to NetApp ...
https://kb.netapp.com/app/answers/answer_view/a_id/1087137/~/how-to-configure-autosupport-in-ontap-9-
Set -mail-hosts to one or more mail hosts, separated by commas. Set a maximum of five. Configure a port value for each mail host by specifying a colon and port number after the mail host name: for example, mymailhost.example.com:5678, where 5678 is the port for the mail host. Set -from to the email address that sends the AutoSupport message.
https://library.netapp.com/ecmdocs/ECMP1368862/html/GUID-BBCB6CA0-88BF-4C94-9048-9643769F4BAB.html
Specifies the maximum email message size for SMTP (email) transfers of AutoSupport messages. This option applies to all messages sent to autosupport.to, autosupport.noteto, and autosupport.partner.to. It also applies to messages sent to NetApp technical support if autosupport.support.transport is smtp. You should set this value to the email ...
https://kb.netapp.com/app/answers/answer_view/a_id/1030651/~/how-to-enable-relaying-for-autosupport-e-mails-on-microsoft-exchange-2003
Note: NetApp recommends HTTP/HTTPS instead of SMTP as a best practice.If HTTP/HTTPS is not an option, follow the steps below to allow relaying for Autosupport delivery: To review the Benefits of using HTTPS or enable refer to Data ONTAP Autosupport and On Demand Configuration NetApp has provided basic steps to configure your Exchange mailhost, we do not cover every Version.
https://library.netapp.com/ecmdocs/ECMP1368862/html/GUID-91C43742-E563-442E-8161-17D5C5DA8C19.html
An automated response from the NetApp mail handler should have been sent to these email addresses. Optional: Confirm that the AutoSupport message is being sent to your internal support organization or to your support partner by checking the email of any address that you configured for the autosupport.to , autosupport.noteto , or autosupport ...
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sag/GUID-91C43742-E563-442E-8161-17D5C5DA8C19.html
You can configure a port value for each mail host by specifying a colon and port number after the mail host name: for example, mymailhost.example.com:5678, where 5678 is the port for the mail host. Set -from to the email address that sends the AutoSupport message.
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sag/GUID-DF931E89-B833-4DED-83B5-A97F7EC97425.html
AutoSupport is a mechanism that proactively monitors the health of your system and automatically sends messages to NetApp technical support, your internal support organization, and a support partner. Although AutoSupport messages to technical support are enabled by default, you must set the correct options and have a valid mail host to have messages sent to your internal support organization.
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-cmpr-930/system__node__autosupport__modify.html
cluster1::> system node autosupport modify -node node3 -state enable -mail-hosts smtp.example.com -from [email protected] -to [email protected] -support enable -transport https -noteto [email protected] -retry-interval 23m. The following examples show how to modify AutoSupport URLs when using IPv6 address literals:
How to find Netapp Change Autosupport Mail information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
