Searching for In Port Channel Only Support Dot1q Trunk Encapsulation information? Find all needed info by using official links provided below.
https://www.cisco.com/c/en/us/support/docs/switches/catalyst-4000-series-switches/23408-140.html
Nov 16, 2007 · When you use a Catalyst L2 fixed configuration switch and any Catalyst 4500/4000 family product that runs CatOS (Catalyst 4003/4006/2948G/2980G), keep in mind that the switches only support dot1q trunking encapsulation. Other Catalyst platforms support both dot1q and Inter-Switch Link Protocol (ISL).
https://www.cisco.com/c/en/us/support/docs/lan-switching/etherchannel/22422-144.html
Feb 26, 2006 · Note: Catalyst 4500/4000 that runs Cisco IOS Software defaults to the L2 port. switchport trunk encapsulation dot1q !--- Setting the trunk encapsulation to dot1q. switchport mode trunk !--- Configured port to be in trunking mode. no ip address channel-group 1 mode on !--- Configured the port to participate in port channel 1 with channel mode on.
https://itexamanswers.net/encapsulation-dot1q-command-on-cisco-router-switch.html
Apr 24, 2018 · First, we will configure the port connected to 2611XM’s Fa0/1 interface to be a trunk on the switch. Routers only support Dot1Q encapsulation. Now we configure the router’s Fa0/1 interface to act as a trunk. First, we remove the ip address on the physical interface.
https://learningnetwork.cisco.com/thread/13157
May 07, 2010 · description Trunk Uplink to House Switch. switchport access vlan 134. switchport trunk encapsulation dot1q. switchport mode access. spanning-tree portfast. channel-protocol pagp. channel-group 1 mode desirable . They were configure by someone outside our company and I thought it strange to see the dot1q listed n an access port.
https://networklessons.com/switching/etherchannel-802-1q-tunneling
In this tutorial we will take a look how you can create an Etherchannel link over 802.1Q tunneling. If you have no idea how 802.1Q tunneling works, it’s best to read my previous tutorial first that covers the basics of 802.1Q tunneling.. Here’s the topology that I will use:
https://networklessons.com/switching/how-to-configure-trunk-on-cisco-catalyst-switch
This is where you can choose between 802.1Q or ISL encapsulation. By default our switch will negotiate about the trunk encapsulation type. SW1(config-if)#switchport trunk encapsulation dot1q SW2(config-if)#switchport trunk encapsulation dot1q. Let‟s change it to 802.1Q by using the switchport trunk encapsulation command.
https://www.reddit.com/r/ccna/comments/3datjp/port_channels_trunking/
Port Channels & Trunking. ... After some googling I found that the fix was to type in switchport trunk encapsulation dot1q. ... Im still studying and its been awhile since I did that part, but i belive its because the 2960s only support dot1q while the layer 3 switches support other protocols. level 2.
https://www.howtonetwork.net/public/708
In the below example we will configure a basic “router on a stick” configuration. First, we will configure the port connected to 2611XM’s Fa0/1 interface to be a trunk on the switch. Routers only support Dot1Q encapsulation.
How to find In Port Channel Only Support Dot1q Trunk Encapsulation information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
