Searching for Ibm Anynet Support information? Find all needed info by using official links provided below.
https://www.ibm.com/support/knowledgecenter/SSEQ5Y_5.9.0/com.ibm.pcomm.doc/books/html/admin_guide20.htm
What Does AnyNet SNA over TCP/IP Do? SNA over TCP/IP is one of the IBM AnyNet software offerings. AnyNet software enables application programs to communicate over different transport networks and across interconnected networks. Using AnyNet, you can reduce the number of transport networks and therefore reduce operational complexity.
https://www.ibm.com/support/pages/ibm-anynet-configuration-sna-over-tcpip-0
Before configuring IBM AnyNet between two IBM OS/400 or IBM i5/OS systems, you must be able to Telnet between both systems using the HOST (target system) name. If unable to Telnet, complete the TCP/IP configuration. 2: References to the source system indicate the system that the APPC application is being initiated on.
https://www.ibm.com/support/pages/ibm-anynet-configuration-sna-over-tcpip
Important Note: Starting in i 7.1, AnyNet (a method used to run SNA communications traffic over IP) is no longer supported.Users of AnyNet are encouraged to migrate to Enterprise Extenders as a replacement. For information about migrating to Enterprise Extenders from AnyNet, see the Migrating from AnyNet to Enterprise Extender topic in the IBM i Information Center.
https://www.ibm.com/support/pages/setting-ibm-anynet-os400-system
To communicate using APPC over TCP/IP support, the systems must allow AnyNet/400 support. To allow AnyNet/400 support, the allow ANYNET support (ALWANYNET) network attribute must be *YES. The following command, issued on all four systems, ensures that the systems allow the use of AnyNet/400 support, which includes APPC over TCP/IP support.
https://www.ibm.com/support/pages/ibm-anynet-and-snaappn-configuration
If you have an existing SNA/APPN configuration and are also configuring IBM AnyNet, the Control Point Name cannot be used from a remote IBM iSeries family of servers Network Attributes for the system for the ANY parameter (RMTCPNAME, RMTLOCNAME).
https://www.ibm.com/support/pages/ibm-objectconnect-ibm-anynet
IBM ObjectConnect does not support user-defined local location names. The value as specified in network attributes for default local location must be used (DSPNETA LCLLOCNAME). If, because of the requirements of IBM AnyNet, you have defined your own location names (not matching the Network Attributes), ObjectConnect will not function correctly.
https://www.ibm.com/support/pages/ibm-anynet-fails-message-cpi5989-code-8004000
Pass-through fails with CPF8921 RC0009. Message CPI5989 with sense code 8004000 is found in the QSYSOPR message queue. In a communications trace, there is no AnyNet …
http://www-01.ibm.com/support/docview.wss?uid=nas8N1010367
The following steps can be used to clean up existing Anynet configurations prior to the configuration Enterprise Extender. This must be done on both systems in which you are going to configure for Enterprise Extender, if Anynet was previously utilized.
http://www-01.ibm.com/support/docview.wss?uid=nas8N1016588
Per APAR MA18298, IBM AnyNet will most likely fail when used over a network using Network Address Translation (NAT) in some firewall between the two IBM AS/400 or IBM iSeries systems. This is because the MPTN (Multi-Protocol Transport Network) architecture incorporates the use of Keep-Alive packets to determine if the connection is still active.
http://archive.ibmsystemsmag.com/blogs/i-can/archive/i-can-use-anynet-in-71/
“AnyNet support is also available in V5R3 through V6R1, however, IBM plans to withdraw support of AnyNet in the release following V6R1; customers currently using AnyNet should start to move to Enterprise Extender in preparation for this.” Is AnyNet supported or not in the 7.1 release? AnyNet isn’t supported on 7.1.
How to find Ibm Anynet Support information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
