Group 3 Support Surface

Searching for Group 3 Support Surface information? Find all needed info by using official links provided below.


CG-DME-16 Pressure Reducing Support Surfaces – Groups 1, 2 & 3

    https://medicalpolicies.amerigroup.com/medicalpolicies/guidelines/gl_pw_a053642.htm
    The use of the group 2 support surface is medically necessary for wound management. When a group 2 pressure reducing support surface is prescribed following a myocutaneous flap or skin graft, continued use is considered medically necessary for up to 60 days from the date of surgery. Group 3 Support Surfaces (as defined in the Definition Section)

Medicare Policy Regarding Pressure Reducing Support ...

    https://www.cms.gov/Medicare/Medicare-Contracting/ContractorLearningResources/downloads/JA1014.pdf
    – A group 3 support surface is covered if the patient has a stage III or stage IV pressure ulcer, is bedridden or chair-bound, would be institutionalized without the use of the group 3 support surface, the patient is under the close supervision of the patient’s treating physician, at least one (1) month of

Pressure Reducing Support Surfaces - Group 3

    https://www.northwoodinc.com/wp-content/uploads/2014/09/Pressure-Reducing-Support-Surfaces-Group-3.pdf
    Pressure Reducing Support Surfaces – Group 3 Medical Policy Pressure Reducing Support Surfaces – Group 3 Description An air fluidized bed is a device employing the circulation of filtered air through ceramic spherules (small, round ceramic objects) that is marketed to treat and prevent pressure sores or treat extensive burns.

Pressure Reducing Support Surfaces - Group 2

    https://www.northwoodinc.com/wp-content/uploads/2014/09/Pressure-Reducing-Support-Surfaces-Group-2.pdf
    Pressure Reducing Support Surfaces – Group 2 codes listed in the table below), and has been on a group 2 or 3 support surface immediately prior to discharge from a hospital or nursing facility within the past 30 days If the member is on a group 2 surface, there should be a care plan established by

Group 2 Pressure Reducing Support Surface (PRSS) (DME MAC ...

    https://www.cgsmedicare.com/pdf/dme_checklists/grp2_support_surfaces_2018re.pdf
    The beneficiary was on a group 2 or 3 support surface immediately prior to the above discharge. NOTE: Coverage following a myocutaneous flap or skin graft is generally limited to 60 days from the date of surgery. Medical records concurrent with the date of service under review support continued use of

GROUP 3 PRESSURE REDUCING SUPPORT SURFACE (PRSS)

    https://www.cgsmedicare.com/pdf/dme_checklists/grp3_support_surfaces_2018re.pdf
    GROUP 3 PRESSURE REDUCING SUPPORT SURFACE (PRSS) DOCUMENTATION CHECKLIST REQUIRED DOCUMENTATION 5 Element Order obtained prior to delivery for the HCPCS code E0194 5 Element order (5EO) contains: Beneficiary’s name Prescribing physician/practitioner’s NPI A description of the item of DME ordered - the description can be either a general

0094 - Group 3 Support Surfaces CMS

    https://www.cms.gov/Research-Statistics-Data-and-Systems/Monitoring-Programs/Medicare-FFS-Compliance-Programs/Recovery-Audit-Program/Approved-RAC-Topics-Items/0094-Group-3-Support-Surfaces
    An air-fluidized bed (Group III Pressure Reducing Support Surface) uses warm air under pressure to set small ceramic beads in motion which simulate the movement of fluid. When the patient is placed in the bed, his body weight is evenly distributed over a large surface area …

Support Surfaces - Russell Medical

    https://www.russellmedical.com/medicare/support-surfaces/
    The beneficiary had a myocutaneous flap or skin graft for a pressure ulcer on the trunk or pelvis within the past 60 days, and has been on a group 2 or 3 support surface immediately prior to discharge from hospital or nursing facility within the past 30 days. Required Documentation for Medicare

Guide to Ordering Group 1 and Group 2 Support Surfaces

    https://corecarenj.com/images/Core_Care_Main/Physician/SupportSurfaceDocument.pdf
    GROUP 1 Support Surface . BACK GROUND- A Group 1 Support Surface is an Overlay (goes over top existing mattress) and is designed to reduce pressure and prevent ulcers. An overlay is typically anywhere between 3 to 5” high. This type of



How to find Group 3 Support Surface information?

Follow the instuctions below:

  • Choose an official link provided above.
  • Click on it.
  • Find company email address & contact them via email
  • Find company phone & make a call.
  • Find company address & visit their office.

Related Companies Support