Searching for Fastethernet0 1 Does Not Support information? Find all needed info by using official links provided below.
https://learningnetwork.cisco.com/thread/70875
May 20, 2014 · And even if i'm trying to give the mtu value less than 1500, it is not accepting. R2(config-if)#mtu 1000 % Interface FastEthernet0/0 does not support user settable mtu. And i tried to setup ip mtu 1000, but i didn't see it changed here: I think i should know the diff. R2(config-if)#ip mtu 1000. R2(config-if)#do show int fa 0/0
https://community.cisco.com/t5/switching/interface-fastethernet0-0-does-not-support-user-settable-mtu/td-p/1628063
% Interface FastEthernet0/0 does not support user settable mtu As Alain already asked you about the IP MTU command, have to tried to issue on router? Please could you let us know what eaxctly your need to we can suggest you any other option (Any issue with any routing protocol or something.
https://community.cisco.com/t5/switching/fastethernet0-1-is-up-line-protocol-is-up/td-p/2643362
q1) what will be the actual situation if i have up an interface but without any physical cable connection. Will it show FastEthernet0/1 is up ? (sorry i really dont have a lab to test except on my GNS) q2) when you mention Line protocol is up = Layer 2 is up = what does it actually check ? is speed and duplex setting part of the check ?
https://community.cisco.com/t5/switching/native-vlan-mismatch-question/td-p/1570167
Oct 12, 2010 · port fa0/13 on 2950 is on vlan 10 my question is why log shows that Native VLAN mismatch discovered on FastEthernet0/13 (10) , even though native vlan on 2950 port fa0/13 is 1 by default. i know to fix this issue either i can config the ports as trunk ports or i can move the port fa0/13 on 2950 from vlan 10 to 20.
https://www.cisco.com/c/en/us/support/docs/switches/catalyst-2900-xl-series-switches/21041-131.html
Nov 03, 2006 · If a device on one side of the channel does not support PAgP, such as a router, the device on the other side must have PAgP set to on. Note: Catalyst 2900XL/3500XL switches do not support PAgP. Catalyst 2950/2955 switches support PagP for channel negotiation with Cisco IOS Software Release 12.1(6)EA2 or later; Cisco IOS Software Release 12.0 ...
https://www.cisco.com/c/en/us/support/docs/lan-switching/etherchannel/22422-144.html
Feb 26, 2006 · An early version of CatOS does not support dot1q trunking. The early version of CatOS that was used in the switches does not support dot1q trunking. Upgrade the CatOS of the switch to a later version that supports both the dot1q trunk and ISL trunk. Related Information. Creating EtherChannel Port Groups Configuring the Switch Ports
https://community.cisco.com/t5/vpn-and-anyconnect/ipsec-tunnel-and-routing-protocols-support/td-p/2091791
Dec 23, 2012 · Solved: Hi Everyone, I read IPSEC does not support Routing Protocols with Site to Site VPN as they both are Layer4. Does it mean that If Site A has to reach Site B over WAN link we should use Static IP on Site A and Site B Router? In my home Lab
https://community.cisco.com/t5/routing/bridge-irb/td-p/580110
3550 DOES NOT support run of the mill bridging for IP, this the reason you are not able to ping between two devices in the same bridge-group. In addition the 3550 does not support BVI, for that as you are well aware it uses SVI.
https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/10570-41.html
Jan 22, 2019 · FastEthernet0/1 and FastEthernet0/3 are in different vlan. In order to finish the configuration, configure another session. This time, use Fa0/4 as a destination SPAN port: ... Catalyst 5500/5000 does not support the filter option that is available with the set span command.
https://www.cisco.com/c/en/us/support/docs/lan-switching/spanning-tree-protocol/24063-pvid-inconsistency-24063.html
Sep 01, 2005 · Non-VLAN 1 STP BPDUs are sent to the PVST+ MAC address (also called the Shared Spanning Tree Protocol [SSTP] MAC address, 0100.0ccc.cccd), tagged with a corresponding IEEE 802.1Q VLAN tag. If the Native VLAN on an IEEE 802.1Q trunk is not VLAN 1: VLAN 1 STP BPDUs are sent to the PVST+ MAC address, tagged with a corresponding IEEE 802.1Q VLAN tag.
How to find Fastethernet0 1 Does Not Support information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
