Drilling Support Beam

Searching for Drilling Support Beam information? Find all needed info by using official links provided below.


Drilling Through Support Beam The Building Code Forum

    https://www.thebuildingcodeforum.com/forum/threads/drilling-through-support-beam.26679/
    Aug 13, 2019 · All of those are together with no space. The engineered support post is nailed to the 2*6 on each side of it. The engineered support post supports three roof trusses. My plan is to drill three or four 3/4" holes right in the middle of the 2*6 and engineered support post. I want to make sure that drilling through this engineered beam is acceptable.

Drilling through I beams - Electrician Talk - Professional ...

    https://www.electriciantalk.com/f29/drilling-through-i-beams-40852/
    Jul 14, 2012 · There seems to be a debate amongst some of the trades in regards to drilling through beams. So how far along the beam and how far apart d o you drill holes? Have the foreman submit an rfi The Following User Says Thank You to angryceltic For This Useful Post: MechanicalDVR (07-19-2012) 07-13-2012, 05:47 PM ...

Drilling main support beam - Houzz

    https://www.houzz.com/discussions/2463736/drilling-main-support-beam
    Jun 30, 2013 · We are rewiring and when we got to the oldest part of the house we discovered that the walls of all the lower floor rooms rest on four main support beams that run in sort of a plus shape. So basically this rules out wiring on one wall of every downstairs room unless it is safe to drill into the beam...

What does the code say about drilling a hole through the ...

    https://www.quora.com/What-does-the-code-say-about-drilling-a-hole-through-the-main-beam
    It depends. First, I don’t know if building codes actually describe this practice but it would be the job of an engineer to determine the effect of drilling a hole in any structural member. Please consult with a licensed professional engineer for ...

Where can I drill a hole in a beam? – Trus Joist Technical ...

    https://www.techsupport.weyerhaeuser.com/hc/en-us/articles/201758910-Where-can-I-drill-a-hole-in-a-beam-
    The maximum size and location of allowable holes is based on product type and depth. Depending on their location in the span, holes up to 2" may be allowed in Microllam® LVL, Parallam® PSL and 1.3E TimberStrand® LSL, and holes up to 4 5/8" may be allowed in 1.55E TimberStrand® LSL.

Problems Drilling Holes Vertical In Structural Beams ...

    https://www.youtube.com/watch?v=DabbLT6Wf9Y
    Jan 03, 2013 · Problems Drilling Holes Vertical In Structural Beams - Building And Construction ... A few years ago I came across a structural beam that was used for a patio with a 2 inch hole drilled through it ...Author: gregvancom

Question regarding a hole in a load bearing beam ...

    http://www.engineering.com/AskForum/aft/1113.aspx
    A home inspection has revealed that a hole has been drilled through a support beam in the garage of a home. It appears to have been done when the home was built over 20 years ago. While the home inspector didn't believe it was an issue, he suggested it ...

Drilling through a large header This Old House

    https://www.thisoldhouse.com/discussions/topic/drilling-through-large-header
    Thanks for the replies. The header is not engineered, it is a piece of dimensional lumber. It extends past the rough opening about two feet, where it butts into a large, vertical support beam. It is held up by a 4 by 4 that is placed against that support beam, which is why it would also be problematic to drill …

Drilling a hole in a Steel I Beam - JLC-Online Forums

    https://forums.jlconline.com/forums/forum/jlc-online-expert-forums/building-science/19275-drilling-a-hole-in-a-steel-i-beam
    Nov 30, 2004 · Re: Drilling a hole in a Steel I Beam OK, I see that we are talking about a steel beam. And, the hole to be drilled is directly over the end support. In that case, the only thing that would be of any concern is whether or not there would be a problem with buckling or crushing from the load above if it is simply supported (and not a space frame).

Will the house fall down if I drilled a hole through a ...

    https://answers.yahoo.com/question/index?qid=20070216103940AAWgJyE
    Feb 16, 2007 · I drill many many holes a day in alot of different structure types for plumbing lines. A half inch hole is not large enough to compromise a support beam. Usually you will hear engineers screaming when you go above 1 1/2". The ideal is not to remove more than 40% of the wood that you drilled through. Dont worry about it. It will be fine.



How to find Drilling Support Beam information?

Follow the instuctions below:

  • Choose an official link provided above.
  • Click on it.
  • Find company email address & contact them via email
  • Find company phone & make a call.
  • Find company address & visit their office.

Related Companies Support