Searching for Does Hp Procurve Support Vtp information? Find all needed info by using official links provided below.
https://community.hpe.com/t5/Switches-Hubs-and-Modems/Does-HP-switches-support-VTP/td-p/4635465
HP Networking switches do not VTP, that is a proprietary protocol only to Cisco. HP Networking switches do support GVRP which is a standards based way of doing VLAN distribution, but very few Cisco products support GVRP. So, you are basically down to the manual creation of VLANs between the Cisco and HP Networking switches.
https://community.hpe.com/t5/Aruba-ProVision-based/what-s-the-similar-technology-with-VTP-on-Procurve-3400/td-p/6326539
No support for VTP as its a Cisco proprietaory protocol, but there is support for GVRP GARP VLAN Registration Protocol. HP's recommendation however was not to use it unless ports were authenticated due to the possibility of a user being able to added themselves to a VLAN that they shouldn't be in, as GVAP will map all VLANs to all uplinks and all switches with GVRP enable.
https://www.experts-exchange.com/questions/28700115/HP-Procurve-VTP-equivalent.html
No support for VTP as its a Cisco proprietaory protocol, but there is support for GVRP GARP VLAN Registration Protocol. HP's recommendation however was not to use it unless ports were authenticated due to the possibility of a user being able to added themselves to a VLAN that they shouldn't be in, as GVAP will map all VLANs to all uplinks and all switches with GVRP enable.
https://learningnetwork.cisco.com/thread/135963
Sep 01, 2019 · You don not need to configure VTP (as far as i know, the HP Switches don't support VTP). You should use dot1q encapsulation for the trunk (HP-Switches and some Cisco switches do not support the cisco proprietary ISL encapsulation).
https://community.hpe.com/t5/Comware-Based/Distributing-VLAN-to-multiple-switches/td-p/6435906
Distributing VLAN to multiple switches I'm new to HP networking, but now I must set up a range of 5900, 6125 and 5500 switches. One thing I have to configure is a dozen or so VLANS across all these switches.
https://www.techrepublic.com/forums/discussions/cisco-to-hp-vtp-setup/
by CG IT · 13 years ago In reply to Cisco-to-HP VTP setup Cisco Switch VTP mode server with other switches as VTP clients in same VTP domain. All switches run same VTP version.
https://community.hpe.com/t5/Aruba-ProVision-based/Procurve-Line-MVRP-Support/td-p/6765491
Procurve Line - MVRP Support. I was wondering if HP had any plans to implement MVRP (802.1ak) open standard in newer firmware. It is a replacement for GVRP that is much less resource intensive and faster. It has been a standard since 2005 so I am suprised that it is not supported.
https://community.hpe.com/t5/Switches-Hubs-and-Modems/quot-VTP-quot-or-trunking-between-2-procurve-switch/td-p/4639640
The configuration on the procurve switches should be ok, but what have you done on the cisco router? Port 48 should not tagged to all vlans, only in the vlan where the ip range from the inside interface of the firewall is connected. Did you configure subinterfaces with 802.1q enabled? VTP is a cisco protocoll and is not supportet on procurve switches.
How to find Does Hp Procurve Support Vtp information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
