Does Cisco Catalyst 2950 Support Multicast

Searching for Does Cisco Catalyst 2950 Support Multicast information? Find all needed info by using official links provided below.


Multicast Catalyst Switches Support Matrix - Cisco

    https://www.cisco.com/c/en/us/support/docs/ip/ip-multicast/29480-167.html
    Feb 26, 2019 · This document provides information on the support of Layer 2 multicast features in various Cisco Catalyst Series Switches. These tables provide more information: CGMP and IGMP Snooping Catalyst Switches Support Matrix. CGMP Feature Catalyst Switches Support Matrix. IGMP Snooping Feature Catalyst Switch Support Matrix

Multicast Does Not Work in the Same VLAN in Catalyst ...

    https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/68131-cat-multicast-prob.html
    Nov 16, 2006 · Any Catalyst switch that runs a Cisco IOS Software release that supports Internet Group Management Protocol (IGMP) snooping Note: Refer to the IGMP Snooping Feature Catalyst Switch Support Matrix section of the document Multicast Catalyst Switches Support Matrix in order to identify these switches.

Solved: enable multicast on 2950/2960 series sw... - Cisco ...

    https://community.cisco.com/t5/switching/enable-multicast-on-2950-2960-series-switches/td-p/1848730
    Re: enable multicast on 2950/2960 series switches No worries John. With so many different product lines and switch series Cisco has, some times it is confusion what devices do layer-2 and what do layer-3, what IOS works with what platforms and features set.

Cisco Catalyst 2950/2960/3750 Multicast... - Cisco Community

    https://community.cisco.com/t5/switching/cisco-catalyst-2950-2960-3750-multicast-traffic-preference/td-p/2504312
    Hello all, we, as a student company act as an ISP for university dormitories. We would like to (if it's possible) deploy QoS to prefer multicast traffic over all other types of traffic. Devices used in network: Acces layer: Cisco Catalyst 2950,

Cisco 2950 and multicasting - Edugeek

    http://www.edugeek.net/forums/wired-networks/80236-cisco-2950-multicasting.html
    Jul 29, 2011 · Cisco 2950 and multicasting We are just starting out with WDS and have tried setting up a multicast session which went OK. apart from it seemed to take the wireless access points down I think its the switches that need configuring to allow multicasting.

Solved: Port Isolation Catalyst 2950 - Cisco Community

    https://community.cisco.com/t5/switching/port-isolation-catalyst-2950/td-p/1226008
    Apr 16, 2009 · Port Isolation Catalyst 2950. I am looking to isolate ports 1-23 from seeing one another, yet I would like to share port 24 (uplink to Internet connection) with each port. (so that each computer could see the Internet, but could not see each other) I've found a million documents which look promising, but never quite address...

Solved: Multicast on Cisco 3560 - Cisco Community

    https://community.cisco.com/t5/switching/multicast-on-cisco-3560/td-p/2330111
    Oct 23, 2013 · Multicast on Cisco 3560. Hello, I am looking for help with multicasts on Cisco 3560 - connected directly to streamer and to two L2 switches (2950, 2960), steamer on its own is linux debian and I am using VLC. So multicast is directly streamed into local Vlan 60 and I can clearly see that it arrives on interface of vlan 60 by ACL I have...

Catalyst 2950 Series Switches Quality of Service ... - Cisco

    https://www.cisco.com/c/en/us/support/docs/lan-switching/lan-quality-of-service/46523-2950qosfaq.html
    Sep 01, 2005 · A. Catalyst 2950 series switches that run the enhanced image (EI) support ingress policing on physical interfaces only. Policers do not have support on VLAN interfaces. Catalyst 2950 series switches that run the standard image (SI) do not support policing. The minimum release with support is Cisco IOS Software Release 12.1. Q.

Cisco Catalyst 2960-X Series FAQ - Cisco

    https://www.cisco.com/c/en/us/products/collateral/switches/catalyst-2960-x-series-switches/qa_c67-728348.html
    Feb 26, 2018 · The Cisco Catalyst 2960X-48FPD-L and C2960X-48FPS-L can support 48 PoE ports with full Class 3 PoE power of 15.4W each, for a total output capacity of 740W. All Cisco Catalyst 2960-X Series Switches with PoE capability support PoE+. A complete list of Cisco Catalyst 2960-X and 2960-XR switches, with their PoE capacities, is given in Table 10.



How to find Does Cisco Catalyst 2950 Support Multicast information?

Follow the instuctions below:

  • Choose an official link provided above.
  • Click on it.
  • Find company email address & contact them via email
  • Find company phone & make a call.
  • Find company address & visit their office.

Related Companies Support