Searching for Does Cisco Asa Support Etherchannel information? Find all needed info by using official links provided below.
https://community.cisco.com/t5/firewalls/asa-does-not-support-connecting-an-etherchannel-to-a-switch/td-p/3820573
The ASA does not support connecting an EtherChannel to a switch stack. If the ASA EtherChannel is connected cross stack, and if the Master switch is powered down, then the EtherChannel connected to the remaining switch will not come up.
https://community.cisco.com/t5/firewalls/asa-etherchannel-to-a-switch-stack/td-p/2694206
The ASA does not support connecting an EtherChannel to a switch stack. If the ASA EtherChannel is connected cross stack, and if the Master switch is powered down, then the EtherChannel connected to the remaining switch will not come up.
https://www.cisco.com/c/en/us/td/docs/security/asa/asa84/configuration/guide/asa_84_cli_config/interface_start.html
Nov 14, 2018 · The ASA does not support connecting an EtherChannel to a switch stack. If the ASA EtherChannel is connected cross stack, and if the Master switch is powered down, then the EtherChannel connected to the remaining switch will not come up. All ASA configuration refers to the logical EtherChannel interface instead of the member physical interfaces.
https://www.cisco.com/c/en/us/td/docs/security/asa/asa92/configuration/general/asa-general-cli/interface-basic.html
Jun 24, 2016 · The device to which you connect the ASA EtherChannel must also support 802.3ad EtherChannels; for example, you can connect to the Cisco Catalyst 6500 switch or Cisco Nexus 7000 switch. The ASA does not support LACPDUs that are VLAN-tagged.
https://www.techrepublic.com/blog/data-center/configure-etherchannel-on-cisco-asa-to-increase-bandwidth-and-achieve-ha/
Configure Etherchannel on Cisco ASA to increase bandwidth and achieve HA Some may say that bandwidth is king. This is true in many cases, especially with higher end video applications becoming more...
https://community.cisco.com/t5/firewalls/asa-8-4-etherchannel-with-sub-interfaces/td-p/1704542
ASA 8.4 etherchannel with Sub Interfaces I am trying to figure out how to create an etherchannel with sub-interfaces on an asa 5520 running 8.4.1 code. It doesn't seem to allow me to configure any type of sub interface on the port-channel or anywhere else once I create it.
https://www.cisco.com/c/en/us/support/docs/lan-switching/etherchannel/21066-135.html
Dec 15, 2005 · If the L3 information does not exist in the packet, the traffic sends over the first link. A wide variety of Cisco routers support EtherChannel. To find a platform or version of code that supports EtherChannel on a Cisco router, use the Cisco Feature Navigator II (registered customers only) . A list of routers and Cisco IOS Software releases that support EtherChannel …
https://www.cisco.com/c/en/us/support/docs/lan-switching/etherchannel/12023-4.html
Jul 09, 2007 · This document presents the concept of load balancing and redundancy on Cisco Catalyst switches with the use of the EtherChannel. This document also covers the Port Aggregation Protocol (PAgP) and trunking support over EtherChannel. This document does not cover how to configure EtherChannel on Catalyst switches.
How to find Does Cisco Asa Support Etherchannel information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
