Searching for Cisco Flexconnect Ap Support information? Find all needed info by using official links provided below.
https://www.cisco.com/c/en/us/support/docs/wireless/wireless-lan-controller-software/200492-Securing-a-flexconnect-AP-switchport-wit.html
Mar 06, 2019 · This means, if the AP supports FlexConnect mode and has locally switched SSIDs configured, it will be able to send tagged traffic. Ensure that vlan support is enabled on the AP and the correct native vlan is configured. AP configuration:-1. If the AP is already joined to the WLC, go the Wireless tab and click on the access point.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-2/configuration/guide/cg/cg_flexconnect.html
Apr 01, 2019 · Whenever a client roams from one FlexConnect access point to another, the FlexConnect group access point calculates the PMKID using the cached PMK. To see the PMK cache entries at the FlexConnect access point, use the show capwap reap pmk command. This feature is supported on Cisco FlexConnect access points.
https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/212481-configure-flexconnect-acl-s-on-wlc.html
Nov 29, 2017 · This document describes the various flexconnect Access Control List (ACL) types and how they can be configured and validated on the Access Point (AP). Prerequisites Requirements. Cisco recommends that you have knowledge of these topics: Cisco Wireless LAN Controller (WLC) that runs code 8.3 and higher; Flexconnect configuration on the WLC ...
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-1/Enterprise-Mobility-8-1-Design-Guide/Enterprise_Mobility_8-1_Deployment_Guide/ch7_HREA.html
Jan 25, 2018 · The Cisco FlexConnect solution also supports Central Client Data Traffic, but it should be limited to Guest data traffic only. ... Check to make sure that the AP model being used has FlexConnect support. The AP model OEAP600 does not support FlexConnect mode. Set QoS to prioritize CAPWAP Control Channel traffic on UDP port 5246.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-3/config-guide/b_cg83/b_cg83_chapter_0101110.html
Jun 15, 2018 · For information about the number of FlexConnect groups and access point support for a Cisco WLC model, see the data sheet of the respective Cisco WLC model. FlexConnect Groups and VLAN Support. You can configure VLAN Support and VLAN ID on a per FlexConnect group basis.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_010001111.html
May 22, 2017 · This feature is supported on Cisco FlexConnect access points only. The PMK cache entries cannot be viewed on Non-FlexConnect access points. ... For information about the number of FlexConnect groups and access point support for a Cisco WLC model, see the data sheet of the respective Cisco WLC model. Configuring FlexConnect Groups.
https://community.cisco.com/t5/wireless-and-mobility/cisco-ap-flexconnect-switch-port-configuration/td-p/1960041
Hi, I have found some samples on the FlexConnect setup for the controller side. However none of the documents mentioned how the switch port should be configured that goes to the controller and AP. At this moment I have a Cisco 5508 configured in CAPWAP mode with 20 APs. I would like to use same co...
How to find Cisco Flexconnect Ap Support information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
