Check Nrpe Ssl Support

Searching for Check Nrpe Ssl Support information? Find all needed info by using official links provided below.


NRPE - CHECK_NRPE: Error - Could Not Complete SSL Handshake

    https://support.nagios.com/kb/article/nrpe-check_nrpe-error-could-not-complete-ssl-handshake-615.html
    Dec 10, 2017 · service nrpe restart SSL Not Compiled In: Another cause of SSL issues is that NRPE was not compiled with ssl enabled. To recompile NRPE with ssl support, browse to your NRPE source directory (usually in /tmp/nrpe-2.15 if you followed the compiling NRPE from source document) and re-compile using the --enable-ssl flag: cd /tmp/nrpe-2.143.6/5(7)

NRPE - v3 Enhanced Security - Nagios Support

    https://support.nagios.com/kb/article.php?id=519
    Jun 21, 2017 · There are arguments that allow the check_npre plugin (command line arguments) and the NRPE client (nrpe.cfg) to define what SSL/TLS version and ciphers are allowed to be used. The strongest method that is negotiated between the plugin and the client will determine what will be used.3.4/5(5)

Certificate based authentication between check_nrpe and ...

    https://support.itrsgroup.com/hc/en-us/articles/360020062154-Certificate-based-authentication-between-check-nrpe-and-NSClient-
    verify mode - Comma separated list of verification flags to set on the SSL socket. none - No verification is made peer - NSClient++ sends client certificate request to the client (check_nrpe) and the certificate returned (if any) is checked against CA certificate. fail-if-no-cert - Terminate the SSL handshake if no client certificate is returned

CHECK_NRPE: (ssl_err != 5) Error - support.nagios.com

    https://support.nagios.com/forum/viewtopic.php?t=50275
    Sep 25, 2018 · This board serves as an open discussion and support collaboration point for Nagios XI. NOTE: Nagios XI customers should use the Customer Support forum to obtain expedited support.

Monitoring FreeBSD with NRPE – Support - ITRS Group

    https://support.itrsgroup.com/hc/en-us/articles/360020252733-Monitoring-FreeBSD-with-NRPE
    How do I gather relevant information to submit with my OP5 Support Ticket? ... Use check_nrpe as the check_command, and put the name of the commands as arguments. An example below: ... Add or renew an SSL certificate for OP5 Monitor; Comments 0 comments.

Building NRPE on Solaris 10 with SSL Support - The Lone ...

    https://lonesysadmin.net/2008/06/11/building-nrpe-on-solaris-10-with-ssl-support/
    Jun 11, 2008 · Building NRPE on Solaris 10 with SSL Support. Bob Plankers. June 11, 2008. System Administration. ... Then I checked that I could start NRPE on the host to be monitored with the -n flag to disable SSL, and was able to run check_nrpe manually with the -n flag and have it work.

Nagios/nrpe: SSL Issues - LinuxQuestions.org

    https://www.linuxquestions.org/questions/linux-security-4/nagios-nrpe-ssl-issues-214284/
    Oct 07, 2004 · A cronjob will call check_nrpe to tell the other Nagios machine to check the disk space or something through port 5666, where the host nrpe daemon is listening. When it returns with the data, the backup machine knows everything is fine, so it'll waits about 5 minutes and do it again, until it receives no response.

NSClient++ / Discussion / Help: CHECK_NRPE: Received 0 bytes.

    https://sourceforge.net/p/nscplus/discussion/445645/thread/54c1af39/
    Sep 06, 2005 · CHECK_NRPE: Received 0 bytes. Are we allowed to connect to the host? Of course, the module is enabled, all hosts are allowed. ... When I use use_ssl=0 with check_nrpe and whatever command (here test) : CHECK_NRPE: Received 0 bytes. Are we allowed to connect to the host? ... Nice, it's work with NRPE v2, but only when SSL support is enabled.

NRPE - CHECK_NRPE: Socket Timeout After n Seconds

    https://support.nagios.com/kb/article/nrpe-check_nrpe-socket-timeout-after-n-seconds-617.html
    Jul 16, 2017 · Problem Description. This KB article addresses the following NRPE error: CHECK_NRPE: Socket Timeout After n Seconds Assumed Knowledge. The following KB article contains an explanation of how NRPE works and may need to be referenced to completely understand the problem and solution that is provided here:1/5(4)

Certificate based TLSv1+ encryption with NSClient++ ...

    https://support.itrsgroup.com/hc/en-us/articles/360020257693-Certificate-based-TLSv1-encryption-with-NSClient-
    As per default encrypted communication with NRPE & NSClient++ is using ADH cipher (Anonymous Diffie Hellman) and a static predefined 512bit DH key.To achieve a more secure encryption method with a better cipher, ability to disable SSLv2 & SSLv3, we need to create certificates, reconfigure the agent and upgrade check_nrpe used for NRPE checks in OP5 Monitor.



How to find Check Nrpe Ssl Support information?

Follow the instuctions below:

  • Choose an official link provided above.
  • Click on it.
  • Find company email address & contact them via email
  • Find company phone & make a call.
  • Find company address & visit their office.

Related Companies Support