Searching for Autosupport Netapp Proxy information? Find all needed info by using official links provided below.
https://kb.netapp.com/app/answers/answer_view/a_id/1001590/~/what-is-the-autosupport.support.proxy-option%3F-
Nov 27, 2017 · options autosupport.support.proxy URL:Port (for example, www-proxy.netapp.com:8080) There are many possible combinations that can be used, including HTTP arguments and CGI invocations. Contact your local IT department for the correct HTTP proxy syntax.
https://kb.netapp.com/app/answers/answer_view/a_id/1030460/~/how-to-set-up-autosupport-
The autosupport.support.proxy option allows an HTTP proxy to be set, if necessary. This is useful only if autosupport.support.transport is HTTP or HTTPS. Since the web proxy access syntax is usually specific to the site, it is not possible to show all the possible examples.
https://kb.netapp.com/app/answers/answer_view/a_id/1087137/~/how-to-configure-autosupport-in-ontap-9-
If you use a proxy, set -proxy-url to the URL of your proxy. This configuration supports communication with AutoSupport OnDemand and uploads of large files. Use HTTP that is preferred over SMTP: Set -transport to http. If you use a proxy, set -proxy-url to the URL of your proxy.
http://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sag/GUID-91C43742-E563-442E-8161-17D5C5DA8C19.html
If you use a proxy, set -proxy-url to the URL of your proxy. This configuration supports communication with AutoSupport OnDemand and uploads of large files. Use HTTP that is preferred over SMTP. Set -transport to http. If you use a proxy, set -proxy-url to the URL of your proxy.
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sag/GUID-F15E7666-EA7F-463F-9AC1-CFA592BC0196.html
system node autosupport show -fields proxy-url network traceroute -node local -destination proxy_url If any of these routes is not functioning, try the same route from a functioning host on the same subnet as the cluster, using the "traceroute" or "tracert" utility found on most third-party network clients.
https://kb.netapp.com/app/answers/answer_view/a_id/1030087/~/how-to-configure-autosupport-in-data-ontap-
The storage system is on a private network and AutoSupport messages cannot be sent to NetApp due to the lack of physical connection to the Internet. The AutoSupport message is too big in size to fit through the mail server's size filter/policy. AutoSupport messages are not sent for some other reason and they are required to be collected for ...
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.hw-metrocluster-tiebreaker/GUID-EB722A3D-C181-42CB-BBF7-5AEC4AEBD92C.html
By default, AutoSupport messages are sent to NetApp a week after installation of the Tiebreaker software. Events that trigger AutoSupport notification include Tiebreaker software panics, detection of disaster conditions on MetroCluster configurations, or an unknown MetroCluster configuration status.
https://kb.netapp.com/app/answers/answer_view/a_id/1030448/~/how-to-configure-autosupport-for-e-series-systems-
The Legacy E-Series storage system does not send the autosupport data directly. Any additional configuration of firewalls openings or necessary changes in your mail or proxy system may depend on knowing the IP address of your SANtricity storage management station. Ensure that the Storage Manager Event Monitor service is running:
https://library.netapp.com/ecmdocs/ECMP1196798/html/GUID-6F959368-F40F-4621-AD2F-71511ECB3277.html
AutoSupport supports HTTPS, HTTP, and SMTP as the transport protocols for delivering AutoSupport messages to NetApp technical support. All of these protocols run on IPv4 or IPv6 based on the address family to which the name resolves. If you enable AutoSupport messages to your internal support organization, those messages are sent by SMTP.
https://library.netapp.com/ecmdocs/ECMP1368862/html/GUID-BBCB6CA0-88BF-4C94-9048-9643769F4BAB.html
autosupport.support.put_url URL: Indicates where AutoSupport messages for NetApp technical support are sent if autosupport.support.transport is http or https.Each message sent via HTTP or HTTPS is sent as an HTTP PUT request to this URL.
How to find Autosupport Netapp Proxy information?
Follow the instuctions below:
- Choose an official link provided above.
- Click on it.
- Find company email address & contact them via email
- Find company phone & make a call.
- Find company address & visit their office.
